C1
C2
C3
C4
Clear
Unproto (0) Clear

Settings

Station

Connection

AGWPE (Direwolf/TNC) ▼
AGWPE (Direwolf/TNC)
KISS (Direwolf/TNC)

Display

Beacon

Message Board

Sounds

Debug

Packet Font Colors

These colors apply only to the Dark theme. Sent packet payloads keep their fixed color.

⚠ Settings Reset

Settings have been restored to factory defaults. Please close and reopen the app for all changes to take effect.

Disable beacon?

⚠️ Beacon Not Configured

Please fill in all beacon fields or disable the beacon.

⚠️ Message Board Not Configured

Enter a valid board callsign or disable the message board.

K2K Packet Desktop — Quick Start

Connect

Your callsign, TNC address and port now live in Settings (⚙ gear icon): set Callsign, Host / IP, Port and Protocol. Defaults are 8000 for AGWPE and 8001 for KISS — switching Protocol fills the matching port for you. Then click Connect: the button itself is the status light — green Connect when idle, red Disconnect when you're on the air. There is no separate status dot any more.

Connected Mode (C1–C4 Tabs)

The four tabs C1 through C4 let you run up to four separate connected-mode sessions simultaneously. Click a tab to select it — each tab keeps its own transcript, history and state.

:c CALLSIGN

Type :c followed by a callsign and press Enter to initiate a connected-mode session. Optionally fill the Via field with digipeaters (space-separated, e.g. DIGI1 DIGI2). Example: :c N0CALL or :c N0CALL-3. Those digis are used for this session and shown in the tab label.

:d

Type :d and press Enter to disconnect the current tab's session.

Once connected, type a message and press Enter to send it. Use Shift+Enter for multi-line messages. ↑ / ↓ walk your send history — Up starts at the most recently sent line and goes back from there.

Enter on an empty line sends a bare CR. It appears in the transcript as [CR]. Kantronics KNet nodes only print their prompt after a CR, and a KPC3 node aborts a connect it has started when it receives one — so this is how you get a prompt from a silent node, or cancel a call in progress.

Unproto Mode (UI Frames)

The right panel displays all received and sent unproto (UI) frames. You can transmit unproto frames using the input fields at the bottom:

  • To — destination callsign (required)
  • Via — digipeater path (optional, space-separated)
  • Message — the text to send

Reuse a path you heard: click the digi path (the via text) on any received packet and it drops into the Via box, cursor ready — no retyping DIGI1,DIGI2. Nothing is remembered until you actually send.

↑ / ↓ in the Via and To boxes walk the paths and destinations you have sent with, most recent first.

Simple Unproto shrinks each header to one compact line — it still shows the whole digi path, not just the first hop.
Deduplicate Packets shows each packet once, and when later copies come in through other digis it marks the digis that already repeated it with * — so DIGI1,DIGI2,DIGI3,DIGI4 becomes DIGI1*,DIGI2*,DIGI3*,DIGI4 as the repeats are heard. It is only a view: turn it off and every original copy comes back with its own path.
Only Unproto hides the connected-mode panel and gives the whole window to unproto.

Beacon

Set up an automatic beacon in Settings (⚙): enable it, then set the beacon text, destination (default BEACON), optional Via path, and interval. It transmits on that interval while connected, and a BEACON badge appears in the top bar — click the badge to turn it off.

Message Board (PBBS)

Enable it in Settings to run a local packet message board. The PBBS badge in the top bar opens the admin console — messages you compose there stay local and never go over RF.

Fonts & Looks

App Font Size (10–25, default 18) is the master knob — the whole interface, top bar included, scales with it. Connected Mode and Unproto font sizes are offsets from that base (−5 to +5, default −2), so you set one overall size and fine-tune each pane. Settings also has the light/dark theme.

Tips

- Auto-connect — enable in Settings to connect on startup.
- Clear buttons wipe the message log or the unproto display.
- Retry indicator — shows T1 retry count and timeout during connected-mode sends.
- Raw KISS — enable in Settings to see raw hex KISS frames instead of decoded messages.
- Logs — the folder button (📂) opens the log directory; each day writes its own YYMMDD_<kind>.log file.
- Settings, history and board data are saved to disk and persist across restarts.

Message Board Admin local console — nothing goes over RF